Ridemalibu Motorcycle Rentals & Tours – Los Angeles CA
  1. Ciao Guest - we've been proud to harbor such wonderful Guzzisti camaraderie since 2005, for FREE. Times have changed, and so have the attitudes and expectations of far too many. Starting Jan 1, 2020, we will likely be shifting to a paid to participate format. You will still be able to read for free. This should alleviate all of the negativity that the free social media channels have created. If you are a donor or customer of ours, you're in, just use the Contact tab above if your account is not already promoted, or you can Upgrade your account once signed in. Or the Donate tab above is another option. We look forward to continuing this service to the Guzzi community, but it is not cheap or easy to host and maintain. We wish you the best for the Holidays and in the New Year.

Recent Activity

Activity stream for all registered members at GuzziTech Forums.

  1. mylovelyhorse replied to the thread Refurbishing my 2007 Norge.

    It’s windy and wet this morning. I shall be grateful for the big Norge fairing as I venture out to take the bike to Baldrick in...

    Dec 5, 2019 at 11:04 PM
  2. V700Steve replied to the thread What is this wire for ?.

    It looks alot like this one https://www.guzzitech.com/forums/threads/what-is-this-for.20196/

    Dec 5, 2019 at 5:28 PM
  3. Darrin Koroll replied to the thread What is this wire for ?.

    i would expect that to come from the battery though. no? To me it looks as though it was factory from the harness near the tail light.

    Dec 5, 2019 at 5:12 PM
  4. SMTCapeCod liked GT-Rx®'s post in the thread V7 III Fuel Filter Not Replaceable?.

    I did a video on it yesterday... I'll pin this thread also. Goes without saying best to run the fuel low or drain the tank as we did for...

    Dec 5, 2019 at 5:02 PM
  5. SMTCapeCod replied to the thread GTM V7 III & V9 Exhaust options & Dyno runs.

    PM sent.

    Dec 5, 2019 at 4:40 PM
  6. bentombed replied to the thread lemans IV fork seals.

    thank you - i was a bit unsure about removing the caps, my old BMW had oil caps making the process very simple.

    Dec 5, 2019 at 3:32 PM
  7. bentombed liked Kevin.NZ's post in the thread lemans IV fork seals.

    Generally: raise the wheel, you take the caps off 1st to relieve the spring pressure and take the springs out, put a cloth over the caps...

    Dec 5, 2019 at 3:31 PM
  8. lucydad liked Mayakovski's post in the thread 2020 V7 III New Model Announcement.

    Because the V7 III is still a fantastic bike.

    Dec 5, 2019 at 3:17 PM
  9. Stu69 posted a new thread.

    v7iii power loss

    hello everyone , had my v7 iii special new from last year , beautiful bike , mostly very happy . However just few months after buying I...

    Forum: V7/V85/V9 Chat & Tech

    Dec 5, 2019 at 2:54 PM
  10. MatadorMkV replied to the thread Rear Cast Wheel Dust Cap?.


    Dec 5, 2019 at 2:33 PM
  11. dududuckling liked jefrs's post in the thread V7III First Service.

    Whilst the spark plugs are NGK CBR8EB-9 the "-9" means they come out of the box at 0.90mm gap which is far too wide and will cause...

    Dec 5, 2019 at 1:33 PM
  12. dududuckling liked vagrant's post in the thread V7III First Service.

    don't use 2L of engine oil. start with 1.5 when changing the oil filter too and add if necessary after getting it warmed up. 1.7 will...

    Dec 5, 2019 at 1:32 PM
  13. Darrin Koroll posted a new thread.

    What is this wire for ?

    Greetings all. New to me 2013 Stelvio owner here. Norge owner for the past 5. Just going over my new mount and i came across this...

    Photo 2019-11-29, 6 01 00 PM.jpg

    Forum: CARC

    Dec 5, 2019 at 1:18 PM
  14. jared p replied to the thread Looking in Spokane,WA.

    Give Optimum Performance Motorsports a call, they're outside Seattle https://opmotorsports.com/vehicle/moto-guzzi-v7-iii-carbon-dark/...

    Dec 5, 2019 at 11:20 AM
  15. stelvio1962 replied to the thread Gear oil for Stelvio.

    Hi Darrin....do you want to meet and talk "Stelvio" ?

    Dec 5, 2019 at 10:56 AM