GTM v2.0 Fender Elim Kit

[GTM®]

All, for those considering a V7 Fender Elim Kit, my newest version will fit '09 to current V7 models (Mk I-III - Racer models ONLY without the rear seat cowling) with plastic rear fenders. Does NOT fit the V7-850 E5. Prototype shown below, final versions are black powder-coated as shown HERE. I will offer it in three options; First as shown below in which you can use the Rizoma run/stop/turn IRIDEs shown HERE, along with a single LED plate light or a CNC plate surround I offer HERE. Or run your stock turns or my favorite M-Pins HERE, along with a large round LED brake light I have on the V7 TTK kit shown HERE. You still may need a plate light by law - see LED surround link above.
These are 100% made-in-house on our CNC-Plasma table at my shop @ GTM in Orange, CA.

Wiring info:
Purple: ground
Yellow: running & plate
Green or Grey: Stop
Blue: L turn
Red: R turn

Round GT LED:
Blue: Running light
Yellow: Brake light
Black: Ground


u

 

[Stradagene]

Very nice! I was waiting for this after seeing the V9 fender eliminator.
Can you do an install on Sunday??

 

[GTM®]

Very nice! I was waiting for this after seeing the V9 fender eliminator.
Can you do an install on Sunday??

Thanks Chris, so you would want one with the same round LED brake light as my V9 kit?
M-F install only.

 

[GR1]

Compatible with H&B rear rack ('16 v7ii stone)?

 

[GTM®]

Compatible with H&B rear rack ('16 v7ii stone)?

I would need to verify the turn signal positioning to the rack, but I believe it should work.

 

[GR1]

Excellent. Well it'll be on my list then but a handful of more important (to me) things to do first (so realistically it'll be a few months probably). Looks clean, well done

 

[SirIzak]

Looks great! Is there still any storage under the seat with this installed?

 

[GTM®]

Looks great! Is there still any storage under the seat with this installed?

Yes. Still retains it, arguably even more since it's now just a flat shelf.

 

[Migs]

Been looking for something like this lately. What's the license plate bolt mounting distance? Assume it's designed for a US plate. I'm in Canada and I think our plates are slightly different. I've had to drill a few of my plates over the years.

 

[Poppe]

Our GTM Guzzi V7 Fender Elim Kit for all '09-17 models. v2.1 shown with Rizoma Iride running/brake/turns and CNC plate surround light. v2.2 will utilize our 2.75" LED brake light and #motogadgetpin turns. All available here on our online Store soon. 100% made in house @ GTMotocycles

View attachment 13603

This is so dope with that surround light. If I could some how get the round light to work along with the Moto Guzzi rack I'm installing, I'd die. But I don't think that's possible, so the MotoGadet's are perfect! I'm pumped.

 

[GTM®]

Been looking for something like this lately. What's the license plate bolt mounting distance? Assume it's designed for a US plate. I'm in Canada and I think our plates are slightly different. I've had to drill a few of my plates over the years.

Since we make them in house now, I can tweak the design fairly easily for a few more $'s. Ping me direct email; Todd at GuzziTech.com

 

[GTM®]

This is so dope with that surround light. If I could some how get the round light to work along with the Moto Guzzi rack I'm installing, I'd die. But I don't think that's possible, so the MotoGadet's are perfect! I'm pumped.

Are you asking if the two Rizoma lights shown would fit the stock rack below? I would say for sure no, but I might have a solution. Write me direct email when you are ready.

 

[Poppe]

Are you asking if the two Rizoma lights shown would fit the stock rack below? I would say for sure no, but I might have a solution. Write me direct email when you are ready.

View attachment 13653

Well the goal would be to get a circular light like your V9, but while doing a tail tidy. This might not work though since it doesn't have anywhere to attach, I'm guessing. Otherwise, if I can't do that, the goal would be to do something like your Rizoma lights or something like that - all with the goal of being visible with the rack installed and some packs on the side for traveling!

I'll shoot you an email when I get closer to being able to get the kit to see what the options are and what you might think is a good solution.

 

[GTM®]

Well the goal would be to get a circular light like your V9, but while doing a tail tidy. This might not work though since it doesn't have anywhere to attach, I'm guessing.

Gotcha, well the tidy and round LED is easy. Just fitting the turns might be the challenge, however I know we can resolve that also, if nothing else with my plate light surround like this one here; https://www.guzzitech.com/store/product/led-plate-light-surround-with-turn-signals/

 

[Poppe]

Gotcha, well the tidy and round LED is easy. Just fitting the turns might be the challenge, however I know we can resolve that also, if nothing else with my plate light surround like this one here; https://www.guzzitech.com/store/product/led-plate-light-surround-with-turn-signals/

This is great news. And that's a great idea too! I've always had my eye on those plate lights you have.

 

[GTM®]

v2.2 Fender Elim Kit with our larger round LED brake light for those asking. Shown with Stone and Racer seat. Thoughts from those buying?

 

[Poppe]

v2.2 Fender Elim Kit with our larger round LED brake light for those asking. Shown with Stone and Racer seat. Thoughts from those buying?

View attachment 13687

I really can't say enough how great this kit looks with that brake light.

 

[jws8439]

They look great! Any idea when these will be available for purchase on the site?

 

[GTM®]

They look great! Any idea when these will be available for purchase on the site?

I should have them online next week. They are at the powder-coater now. Which version do you want?

 

[GTM®]

We just finished protoyping the GTM v2.2 FEK, that will work with the stock grab rail on the V7 III models (Special or Anniversario).
Interest? I have a few in the shop that will be getting them, but I will not make anymore unless on paid order for those here. Post below or email me direct if you want one; Todd at GuzziTech.com