• Ciao Guest - You’ve landed at the ultimate Guzzi site. NEW FORUM REGISTRATIONS REQUIRE EMAIL ACTIVATION - CHECK YOUR SPAM FOLDER - Use the CONTACT above if you need help. New to the forum? For all new members, we require ONE post in the Introductions section at the bottom, in order to post in most of the other sections. ALWAYS TRY A SEARCH BEFORE STARTING A NEW TOPIC - Most questions you may have, have likely been already answered. DON'T BE A DRIVE-BY POSTER: As a common courtesy, check back in and reply within 24 hours, or your post will be deleted. Note there's decades of heavily experienced Guzzi professionals on this site, all whom happily give endless amounts of their VALUABLE time for free; BE COURTEOUS AND RESPECTFUL!
  • There is ZERO tolerance on personal attacks and ANY HYPERLINKS to PRODUCT(S) or other competing website(s), including personal pages, social media or other Forums. This ALSO INCLUDES ECU DIAGnostic software, questions and mapping. We work very hard to offer commercially supported products and to keep info relevant here. First offense is a note, second is a warning, third time will get you banned from the site. We don't have the time to chase repeat (and ignorant) offenders. This is NOT a social media platform; It's an ad-free, privately funded website, in small help with user donations. Be sure to see the GTM STORE link above; ALL product purchases help support the site, or you can upgrade your Forum profile or DONATE via the link above.
  • Be sure to see the GTM STORE link also above for our 700+ product inventory, including OEM parts and many of our 100% Made-in-SoCal-USA GTM products and engine kits. In SoCal? Click the SERVICE tab above for the best in service, tires, tuning and installation of our products or custom work, and don't miss our GT MotoCycles® (not) art on the BUILDS tab above. WE'RE HERE ONLINE ONLY - NO PHONE CALLS MADE OR RECEIVED - DO NOT EMAIL AND ASK QUESTIONS OR ASK TO CALL YOU.
  • Like the new V100, GuzziTech is full throttle into the future! We're now running on an all-new server and we've updated our Forum software. The visual differences are obvious, but hopefully you'll notice the super-fast speed. If you notice any glitches or have any issues, please post on the Site Support section at the bottom. If you haven't yet, please upgrade your account which is covered in the Site Support section or via the DONATE tab above, which gives you full site access including the DOWNLOADS section. We really appreciate every $ and your support to keep this site ad-free. Create an account, sign in, upgrade your account, and enjoy. See you on the road in 2024.

Rear dirve seal replacement for Quota

Rafael

GT Reference
Joined
Feb 16, 2009
Messages
1,096
Location
San Leandro, CA
Now I know why folks leave all the goop/dirt build up on the rear drive. I took the rear wheel of the inspect the splines and grease them. Decided to clean it up, I guess I used the wrong chemical and swole up the seal and caused a leak. I dried it with compressed air, but that wasn't engouhg. Anyway, I haven't replaced one of these before, I understand it's easy, maybe that's why the manual doesn't cover it. Do you need a special too to reseat the seal?
Any tips or precautions would be appreciated.

thanks, Rafael
 
Special tools aren't really necessary, but having a good seal driver set will help. Main thing is don't scratch the hub when removing the seal, nor gouge the bearing cover. The seal driver with a lip helps to seat the seal over the hub. If you are very careful with say a socket place backwards on an extension and tapping around the perimeter of the seal until it is flush you should be OK.
 
Thanks John, it was easy; took 15 minutes. I used a rubber mallet and pounded lightly until it got to the original seat depth. The face of the old seal was raised about 2mm above the adjacent carrier face, so I put it back the same way. We'll see how long it will last. Anyone know of a good seal draive set? thx
 
Back
Top