Sourced from the Owner's Manual, but worthy of a quick post here:
MGCT (Moto Guzzi Controllo Trazione - Traction Control):
Scrolling through TRIP 1 or TRIP 2 by short pressing the MODE control to the left or right, it is possible to display the MGCT option.
By short pressing the MODE control in a central position the rider can access the MGCT function.
By moving the selector to the right, holding it down, the system turns on and the value "1" (minimum intervention) appears on the display.
The MGCT warning light will flash.
By moving the selector to the right, pressing it briefly, the intervention level increases up to a maximum of "3" (Maximum intervention).
EVERY TIME THE SET VALUE IS MODIFIED, THE NUMERIC SYMBOL IS DISPLAYED IN NEGATIVE (BLINKS) FOR 2 SECONDS BEFORE BEING CONFIRMED
To deactivate the system, from value "1", turn the selector to the left, holding it down, until the value "-" appears.
The MGCT warning light will be on steady.
To exit the MGCT function short press the selector or set off on the motorcycle.
NOTES:
CALIBRATION IS NEEDED TO OPTIMIZE THE MGCT FUNCTION IN THE EVENT OF CHANGING A TIRE SIZE. IF TIRES OTHER THAN THOSE INDICATED IN THIS USE AND MAINTENANCE BOOKLET ARE USED, TO OBTAIN THE SAME PERFORMANCE FROM THE MGCT SYSTEM THE SETTING LEVELS OF THE SYSTEM ITSELF MAY NEED TO BE MODIFIED.
Select the CALIBRATION function from the configuration menu to access the CALIBRATION function.
When the CALIBRATION function is selected (with vehicle at a standstill), a screen is shown with the following message at the bottom of the display:
CALIBRATING:
To calibrate the MGCT (Moto Guzzi Controllo Trazione) system, ride about 10 seconds on a flat, straight section of road in second gear at a speed of 30 +/- 2 km/h (18.64 +/- 1.24 mph) until CALIBRATION appears on the display.
NOTES:
CAUTION:
MGCT (Moto Guzzi Controllo Trazione - Traction Control):
Scrolling through TRIP 1 or TRIP 2 by short pressing the MODE control to the left or right, it is possible to display the MGCT option.
By short pressing the MODE control in a central position the rider can access the MGCT function.
By moving the selector to the right, holding it down, the system turns on and the value "1" (minimum intervention) appears on the display.
The MGCT warning light will flash.
By moving the selector to the right, pressing it briefly, the intervention level increases up to a maximum of "3" (Maximum intervention).
EVERY TIME THE SET VALUE IS MODIFIED, THE NUMERIC SYMBOL IS DISPLAYED IN NEGATIVE (BLINKS) FOR 2 SECONDS BEFORE BEING CONFIRMED
To deactivate the system, from value "1", turn the selector to the left, holding it down, until the value "-" appears.
The MGCT warning light will be on steady.
To exit the MGCT function short press the selector or set off on the motorcycle.
NOTES:
- THE FIRST TIME THE BATTERY IS CONNECTED THE MGCT WARNING LIGHT IS ON STEAD (SYSTEM NOT ACTIVE)
- ONCE THE MOTORCYCLE IGNITION SWITCH IS TURNED OFF, AT THE NEXT START UP THE MGCT SYSTEM MAINTAINS THE PREVIOUSLY SELECTED SETTINGS.
CALIBRATION IS NEEDED TO OPTIMIZE THE MGCT FUNCTION IN THE EVENT OF CHANGING A TIRE SIZE. IF TIRES OTHER THAN THOSE INDICATED IN THIS USE AND MAINTENANCE BOOKLET ARE USED, TO OBTAIN THE SAME PERFORMANCE FROM THE MGCT SYSTEM THE SETTING LEVELS OF THE SYSTEM ITSELF MAY NEED TO BE MODIFIED.
Select the CALIBRATION function from the configuration menu to access the CALIBRATION function.
When the CALIBRATION function is selected (with vehicle at a standstill), a screen is shown with the following message at the bottom of the display:
CALIBRATING:
To calibrate the MGCT (Moto Guzzi Controllo Trazione) system, ride about 10 seconds on a flat, straight section of road in second gear at a speed of 30 +/- 2 km/h (18.64 +/- 1.24 mph) until CALIBRATION appears on the display.
NOTES:
- ONCE THE MESSAGE 'CALIBRATING' CEASES TO BE DISPLAYED, STOP THE VEHICLE, TURN THE IGNITION SWITCH OFF AND LEAVE OFF FOR AT LEAST 30 SECONDS TO COMPLETE THE CALIBRATION PROCEDURE. THIS ALLOWS THE CALIBRATION TO BE STORED IN THE MEMORY.
- TURN THE IGNITION SWITCH OFF TO ABORT THE CALIBRATION PROCEDURE.
- WHEN CALIBRATION IS CARRIED OUT THE TRACTION CONTROL SYSTEM AUTOMATICALLY DEACTIVATES (IF IT WAS PREVIOUSLY ACTIVATED).
CAUTION:
- WHEN THE MOTORCYCLE IS IN RESERVE MODE, IT IS NOT POSSIBLE TO CARRY OUT THE CALIBRATION PROCEDURE.